Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
11.1. Specifications
11.2. A hydrodrive of brakes
11.3. Tubes and hoses
11.4. Колодки
11.5. A brake disk
11.6. Drums
11.7. A support of a forward brake
11.8. A support of a back brake
11.9. The wheel cylinder
11.10. The main cylinder
11.11. A brake pedal
11.12. The vacuum amplifier of brakes
11.13. The amplifier of brakes and the return valve
11.14. The lever of a manual brake
11.15. Cables of a manual brake
11.16. Adjustment of a manual brake
11.17. The switch of a signal of braking
11.18. The switch of a lamp of a manual brake
11.19. Antiblocking system
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



11-10-glavnyjj-cilindr.html

11.10. The main cylinder

Removal

PERFORMANCE ORDER
1. Turn away a stopper and remove a liquid from a nutritious tank (or extort, having turned away the union on a wheel).
2. Disconnect wires from the gauge of level of a liquid.
3. Clear the union on the main cylinder.
4. Designate the union that at assemblage to attach on former places.
5. Turn away a nut of unions, cautiously get tubes and muffle apertures.
6. Immediately wipe the spilt liquid.
7. Turn away a nut and remove the main cylinder from the vacuum amplifier.
8. Remove from the cylinder a lining.

Dismantling


The prevention

Before dismantling get ремкомплект to the cylinder of that type which is established on your car.


PERFORMANCE ORDER
1. Remove a nutritious tank, get a tank sealant (if it is provided).
2. Unbend ears and remove a cap.
3. On cars with ABS-system push the first piston wooden оправкой and turn away a lock bolt.
4. Get a lock ring (if it is provided).
5. Get from the cylinder a washer, pistons, springs and plates, having remembered an order of their installation. If necessary push out the piston a stream of compressed air, having clamped the cylinder in a vice.
6. Carefully wash out all details in spirit or a brake liquid and immediately dry.
7. Check up a condition of details, at detection of deterioration or damages replace. Have in view of that in ремкомплект the main cylinder pistons with sealants enter, уплотнители separately in spare parts are not delivered.
8. If on the cylinder and the piston there are teases, scratches or corrosion traces replace the cylinder in gathering.
9. Before assemblage grease the piston, cuffs and the cylinder with a brake liquid.
10. Establish in the cylinder all details in a former order.
11. The piston enter circular motions not to damage a cuff.
12. Establish a washer on an end face of the first piston. On cars with ABS-system the lock bolt should coincide with a groove in the second piston.
13. On cars with ABS-system compress pistons and wrap a lock bolt.
14. Compress pistons and fix a new cap (it is delivered in ремкомплекте).
15. Bend cap ears.
16. Check up a condition of sealants of a tank, if necessary replace.
17. Dress уплотнители and establish a tank.

Installation
PERFORMANCE ORDER
1. Wipe surfaces of the cylinder and the vacuum amplifier and dress a new lining.
2. Establish the cylinder on the vacuum amplifier, having convinced. That the amplifier pusher enters into the cylinder on the centre.
3. Tighten nuts with the set moment.
4. Establish tubes on the put labels, turn and tighten the union.
5. Fill in a liquid in a tank and remove air from a hydrodrive.
6. Before departure check up work of brakes.



11.9. The wheel cylinder

11.11. A brake pedal