Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
11.1. Specifications
11.2. A hydrodrive of brakes
11.3. Tubes and hoses
11.4. Колодки
11.4.1. Колодки forward brakes
11.4.2. Колодки back brakes
11.4.3. Колодки back drum-type brakes
11.5. A brake disk
11.6. Drums
11.7. A support of a forward brake
11.8. A support of a back brake
11.9. The wheel cylinder
11.10. The main cylinder
11.11. A brake pedal
11.12. The vacuum amplifier of brakes
11.13. The amplifier of brakes and the return valve
11.14. The lever of a manual brake
11.15. Cables of a manual brake
11.16. Adjustment of a manual brake
11.17. The switch of a signal of braking
11.18. The switch of a lamp of a manual brake
11.19. Antiblocking system
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



11-4-2-kolodki-zadnikh-tormozov.html

11.4.2. Колодки back brakes

Replacement

PERFORMANCE ORDER
1. Lift a back part of the car and establish on supports.
2. Remove back wheels.
3. Disconnect a cable of a manual brake at first from an arm, then from the support lever.
4. Turn out support fingers.
5. Remove a support body.
6. After support dismantling a pedal of a brake not to press.
7. Fix a support so that the hose did not stretch.
8. Remember orientation of lateral and antinoise overlays on колодках (antinoise overlays are provided on a part of cars and are located at the top and bottom end faces колодок).
9. Remove overlays.
10. Remove колодки.
11. Remove spring clamps.
12. Check up a thickness of frictional overlays.
13. If the thickness at least one overlay is less than norm, or колодки are strongly polluted, replace all колодки in the complete set with one axis.
14. Find and eliminate the pollution reason.
15. It is forbidden to rearrange колодки for the purpose of deterioration indemnification.
16. If a condition колодок satisfactory clear them, having removed the eaten dirt and large particles.
17. Clear places for колодок in a support.
18. Before assemblage check up freedom of moving of fingers in an arm and a support, and also integrity of rubber covers.
19. Check up a condition of sealants of the piston, corrosion presence on the piston and traces подтекания.
20. If колодки will vary, the piston should be drowned in the cylinder for what turn the piston круглогубцами clockwise, simultaneously pressing into the cylinder.
21. At piston displacement watch liquid level, surplus of a liquid above a mark on a tank should be removed the MOVE a rubber pear or a syringe.
22. Slightly grease plates колодок, linings and spring скобы with special antinoise greasing.
23. Have in view of that new колодки are delivered in spare parts with an antinoise covering and their greasings it is not required.
24. Establish antinoise скобы, колодки and overlays on former places (скобы and overlays are provided on a part of cars).
25. Establish a support body. The ledge on a back part колодок should come into piston dredging.
26. If necessary tighten the piston.
27. Grease the bottom finger of a support with fixing structure, wrap fingers and tighten with the set moment.
28. Check up freedom of moving of a support on fingers.
29. Attach a cable of a manual brake in sequence of return to removal, establish an arm of a cable and spring скобу (if it is provided). The ledge on an arm should come into dredging on a support body.
30. Repeat the described actions for a brake of other back wheel.
31. Adjust a manual brake.
32. Press some times a brake pedal.
33. Establish wheels, lower the car.
34. Check up liquid level.
35. Before departure check up work of brakes.


11.4.1. Колодки forward brakes

11.4.3. Колодки back drum-type brakes