Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
11.1. Specifications
11.2. A hydrodrive of brakes
11.3. Tubes and hoses
11.4. Колодки
11.4.1. Колодки forward brakes
11.4.2. Колодки back brakes
11.4.3. Колодки back drum-type brakes
11.5. A brake disk
11.6. Drums
11.7. A support of a forward brake
11.8. A support of a back brake
11.9. The wheel cylinder
11.10. The main cylinder
11.11. A brake pedal
11.12. The vacuum amplifier of brakes
11.13. The amplifier of brakes and the return valve
11.14. The lever of a manual brake
11.15. Cables of a manual brake
11.16. Adjustment of a manual brake
11.17. The switch of a signal of braking
11.18. The switch of a lamp of a manual brake
11.19. Antiblocking system
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



11-4-kolodki.html

11.4. Колодки


The prevention

Колодки vary only in the complete set on one axis. At clearing колодок a dust and a dirt to delete wiping by rags moistened in spirit, it is forbidden to blow.


Replacement

PERFORMANCE ORDER
1. Lift a forward part of the car and establish on supports.
2. Remove forward wheels.
3. Pull a support on itself that the piston has entered into the cylinder, watching liquid level in a tank.
4. If necessary press the piston by means of a clamp.
5. Turn away support fingers (стелки).
6. Remove a support from a disk.
7. Have in view of that external колодка can remain on an arm.
8. After support removal a pedal of a brake not to press.
9. Fix a support so that it did not hang on a hose.
10. Remove adjusting linings.
11. Remove колодки.
12. Remove clamps колодок.
13. Check up a thickness of frictional overlays.
14. If the thickness at least one overlay is less than norm, or колодки are strongly polluted, replace all колодки in the complete set with one axis.
15. Find and eliminate the pollution reason.
16. It is forbidden to rearrange колодки for the purpose of deterioration indemnification.
17. If a condition колодок satisfactory clear them, having removed the eaten dirt and large particles.
18. Clear surfaces прилегания колодок in a support and an arm.
19. Before assemblage check up freedom of moving of fingers in an arm and a support, and also integrity of rubber covers.
20. Check up a condition of sealants of the piston, corrosion presence on the piston and traces подтекания.
21. If колодки will vary, the piston should be displaced to provide a place for колодок.
22. At piston displacement watch liquid level, surplus of a liquid should be removed a rubber pear or a syringe.
23. Slightly grease plates колодок, linings and spring скобы with special antinoise greasing.
24. Establish скобы, колодки and linings in a support arm. External колодка it is established in an arm, and internal – in a support.
25. Be convinced that the clamp internal колодки has come into gearing with the piston.
26. Establish a support, grease support fingers with fixing structure and turn.
27. Tighten fingers with the set moment.
28. Check up freedom of moving of a support on fingers.
29. Repeat the described actions for a brake of other wheel.
30. Press some times a brake pedal.
31. Establish wheels, lower the car.
32. Check up liquid level.
33. Before departure check up work of brakes.


11.3. Tubes and hoses

11.4.1. Колодки forward brakes