Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
11.1. Specifications
11.2. A hydrodrive of brakes
11.3. Tubes and hoses
11.4. Колодки
11.5. A brake disk
11.6. Drums
11.7. A support of a forward brake
11.8. A support of a back brake
11.9. The wheel cylinder
11.10. The main cylinder
11.11. A brake pedal
11.12. The vacuum amplifier of brakes
11.13. The amplifier of brakes and the return valve
11.14. The lever of a manual brake
11.15. Cables of a manual brake
11.16. Adjustment of a manual brake
11.17. The switch of a signal of braking
11.18. The switch of a lamp of a manual brake
11.19. Antiblocking system
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



11-5-disk-tormoza.html

11.5. A brake disk

DISKS OF FORWARD BRAKES


The prevention

Disks vary only in steam and with the complete set колодок.


Check

PERFORMANCE ORDER
1. Lift a forward part of the car and establish on supports.
2. Remove wheels.
3. Slowly rotating, check up a disk condition, if necessary remove колодки.
4. The disk is subject to replacement at presence on it of cracks and traces of deep development.
5. If on a disk the fillet caused by deterioration it is necessary to measure a thickness of a disk was formed.
6. The thickness is measured in several places, both in a place of contact with колодками, and on edge.
7. If the thickness is equal in deterioration places limiting or less the disk is subject to replacement.
8. Check up adjustment of the bearing of a nave then check up palpation of a disk by means of the indicator or laying щупы, for example between a disk and a support arm.
9. If palpation exceeds norm remove a disk, turn and again establish on a nave.
10. If palpation again exceeds norm a disk replace.
11. Check up a disk condition in places of fastening, damages to other places.

Removal

PERFORMANCE ORDER
1. Lift the car and remove a wheel.
2. Turn away two bolts on a support arm, get a support, take aside and fix.
3. If the disk does not vary, put labels of mutual orientation to a disk and a nave.
4. Remove a disk from hairpins of fastening of a wheel.
5. If the disk does not give in to removal displace it, in regular intervals wrapping bolts М8 in special carving apertures.

Installation

PERFORMANCE ORDER
1. Clear demountable surfaces of a nave and a disk.
2. Establish a disk, having combined the put labels (if the removed disk is established).
3. From a new disk remove preservative.
4. Establish a support, wrap bolts with the set moment.
5. Press some times a brake pedal.
6. Establish a wheel, lower the car. Before departure check up work of brakes.

DISKS OF BACK BRAKES


The prevention

Disks vary only in steam and with the complete set колодок.


Check

PERFORMANCE ORDER
1. Lift a back part of the car and establish on supports.
2. Remove wheels.
3. Release a manual brake.
4. Execute the actions described above. If will act in film колодки be guided by the description in subsection 11.4.2.

Removal

PERFORMANCE ORDER
1. Lift a back part of the car and establish on supports.
2. Remove wheels.
3. Turn away bolts and remove an arm of a cable of a manual brake.
4. Disconnect a cable from the lever on a support (on a part of cars get a cover of a cable from скобы).
5. Execute the actions described above.

Installation

PERFORMANCE ORDER
1. Execute the actions described above.
2. Attach a cable to the lever.
3. On a part of cars insert a cable cover in скобу, and a ledge on an arm combine with dredging on a support body.
4. Include a manual brake until the necessary backlash between колодками and a disk will be established.
5. Press some times a brake pedal.
6. Establish a wheel, lower the car.
7. Before departure check up work of brakes.


11.4.3. Колодки back drum-type brakes

11.6. Drums