Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
11.1. Specifications
11.2. A hydrodrive of brakes
11.3. Tubes and hoses
11.4. Колодки
11.5. A brake disk
11.6. Drums
11.7. A support of a forward brake
11.8. A support of a back brake
11.9. The wheel cylinder
11.10. The main cylinder
11.11. A brake pedal
11.12. The vacuum amplifier of brakes
11.13. The amplifier of brakes and the return valve
11.14. The lever of a manual brake
11.15. Cables of a manual brake
11.16. Adjustment of a manual brake
11.17. The switch of a signal of braking
11.18. The switch of a lamp of a manual brake
11.19. Antiblocking system
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



11-7-support-perednego-tormoza.html

11.7. A support of a forward brake

Removal

PERFORMANCE ORDER
1. Lift a forward part of the car and establish on supports.
2. Remove a wheel.
3. For decrease in losses of a liquid densely wrap a tank stopper having laid a polyethylene film, or press hoses.
4. Clear the ring union of a hose and turn away a bolt.
5. Remove two linings.
6. Remove колодки.
7. Turn away the top finger of a support.
8. Remove a support.
9. If necessary it is possible to remove a support arm.

Dismantling

PERFORMANCE ORDER
1. Cautiously clear a support.
2. Get fingers for heads of bolts which screw in fingers.
3. Remove rubber covers of fingers.
4. Remove a lock ring and a cylinder cover.
5. Take the piston, having submitted air from the pump to an union aperture.
6. A wooden stick get a cylinder sealant.
7. Wash out all details in a pure brake liquid or spirit.
8. All уплотнители and covers are subject to obligatory replacement.
9. Check up a support condition, especially carefully examine the piston and an internal surface of the cylinder, the worn out details replace. The support or a support arm separately in spare parts are not delivered.
10. Minor defects on the cylinder are eliminated by polishing by a small skin whereas the piston with the same defects is subject to obligatory replacement. To polish the piston it is forbidden.
11. Check up a condition of carvings on support fingers, люфт fingers in a support should be absent.
12. Blow channels in a support.
13. Before assemblage check up cleanliness of all details.
14. Dip a cylinder sealant into a liquid and establish in a cylinder flute.
15. Dress a cover edge in a cylinder flute, grease with a brake liquid the piston and the cylinder, establish the piston in the cylinder and dress the second edge of a cover on the piston.
16. Dress new covers on support fingers, before installation in a support grease fingers with a brake liquid.

Installation

PERFORMANCE ORDER
1. Establish a support arm, tighten bolts.
2. Establish a support, grease a carving of a bolt of the top finger with fixing structure and wrap a bolt with the set moment.
3. Establish колодки.
4. Check up freedom of moving of a support in an arm.
5. Attach a hose, having established two linings and having tightened a bolt of the ring union.
6. Remove a polyethylene lining from a tank stopper (or remove collars from hoses).
7. Remove air from a hydrodrive of a brake of a wheel (if integrity of other contours was not broken).
8. Press some times a brake pedal.
9. Establish a wheel, lower the car.


11.6. Drums

11.8. A support of a back brake