Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
11.1. Specifications
11.2. A hydrodrive of brakes
11.3. Tubes and hoses
11.4. Колодки
11.5. A brake disk
11.6. Drums
11.7. A support of a forward brake
11.8. A support of a back brake
11.9. The wheel cylinder
11.10. The main cylinder
11.11. A brake pedal
11.12. The vacuum amplifier of brakes
11.13. The amplifier of brakes and the return valve
11.14. The lever of a manual brake
11.15. Cables of a manual brake
11.16. Adjustment of a manual brake
11.17. The switch of a signal of braking
11.18. The switch of a lamp of a manual brake
11.19. Antiblocking system
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



11-8-support-zadnego-tormoza.html

11.8. A support of a back brake

Removal

PERFORMANCE ORDER
1. Lift a back part of the car and establish on supports.
2. Remove a wheel.
3. Release a cover of a cable of a manual brake, disconnect a cable from the lever on a support.
4. For decrease in losses of a liquid densely wrap a tank stopper having laid a polyethylene film, or press hoses.
5. Clear the ring union of a hose and turn away a bolt, muffle apertures.
6. Remove two linings.
7. Remove колодки.
8. Turn away a bolt of the top finger of a support.
9. Remove a support from an arm.
10. If necessary it is possible to remove a support arm from a pin.

Dismantling

PERFORMANCE ORDER
1. Cautiously clear a support.
2. Get fingers for heads of bolts which screw in fingers.
3. Remove rubber covers of fingers.
4. Turn out (to rotate counter-clockwise) and get the piston from the cylinder.
5. Remove a cover.
6. Compress a cylinder spring, having pressed on a cap, and take a lock ring from a cylinder flute.
7. Gradually releasing a spring, get a spring ring, a cap, a spring, a lock plate, a pusher and распорку.
8. A wooden stick get a cylinder sealant.
9. Unhook a spring from the lever of a manual brake, turn away a nut and remove the lever from a support.
10. Wash out all details in a pure brake liquid or spirit.
11. All уплотнители and covers are subject to obligatory replacement.
12. Check up a support condition, especially carefully examine the piston and an internal surface of the cylinder, the worn out details replace. The support or a support arm separately in spare parts are not delivered.
13. Minor defects on the cylinder are eliminated by polishing by a small skin whereas the piston with the same defects is subject to obligatory replacement. To polish the piston it is forbidden.
14. Check up a condition of carvings on support fingers, люфт fingers in a support should be absent.
15. Blow channels of a brake liquid.
16. Before assemblage check up cleanliness of all details.
17. Dress a new cover on the clown of the lever of a manual brake.
18. Establish a spring, a washer and tighten a nut.
19. Grease the clown with a brake liquid and establish on a support.
20. Be convinced that at turn of the lever the groove in the clown is combined with an aperture in a pusher.
21. Dress a lever spring.
22. Dip a new sealant of the cylinder into a liquid and establish in a cylinder flute.
23. Dress on a pusher a new sealing ring and grease with rubber oil распорку and a pusher.
24. Establish all details in a support.
25. Establish a lock plate so that the groove had on a flat part of a pusher, and camber has coincided with deepening in a support.
26. Establish a spring lock ring.
27. Establish a spring and a cap, compress a spring and establish a spring lock ring.
28. Grease an edge of a cover of the cylinder with rubber oil and dress on the piston.
29. Grease with a brake liquid the piston and cylinder walls in a support, screw the piston in the cylinder, rotating clockwise.
30. Dress the second edge of a cover on a support.
31. Dress new covers on support fingers.
32. Replace the rubber plug on the top finger.
33. Before installation in a support grease fingers with a brake liquid.

Installation

PERFORMANCE ORDER
1. Establish a support arm on a pin, tighten bolts.
2. Establish a support, grease a carving of a bolt of the top finger with fixing structure and wrap a bolt with the set moment.
3. Establish колодки.
4. Check up freedom of moving of a support in an arm.
5. Attach a hose, having established two linings and having tightened a bolt of the ring union.
6. Attach a cable of a manual brake to the lever, establish an arm. On a part of cars insert a cable cover in скобу, and a ledge on an arm combine with dredging on a support body.
7. Remove a polyethylene lining from a tank stopper (or remove collars from hoses).
8. Remove air from a hydrodrive of a brake of a wheel (if integrity of other contours was not broken).
9. Press some times a brake pedal.
10. Establish wheels, lower the car.
11. Before departure check up work of brakes.


11.7. A support of a forward brake

11.9. The wheel cylinder