Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
12.1. Specifications
12.2. Bearings of naves of forward wheels
12.3. A rack of a forward suspension bracket
12.4. The bottom lever
12.5. A spherical support of the bottom lever
12.6. The stabilizer of cross-section stability of a forward suspension bracket
12.7. Bearings of back wheels
12.8. Details of a back suspension bracket
12.9. A wheel
12.10. The switch of ignition and the lock of blocking of a steering column
12.11. A steering column
12.12. The steering mechanism
12.13. Covers of steering transfer
12.14. A hydrodrive
12.15. The hydraulic booster pump
12.16. Tips of steering draught
13. A body
14. An electric equipment
 




6ac69956



12-2-podshipniki-stupic-perednikh-koles.html

12.2. Bearings of naves of forward wheels

Replacement

PERFORMANCE ORDER
1. Lift a forward part of the car and establish on supports.
2. Remove a wheel.
3. Remove a disk and a support.
4. Remove the gauge of speed (on cars with ABS-system).
5. Turn away fastening of an arm of conducting and take the gauge aside.
6. Disconnect полуось from only from a nave, take aside and fix (subsection 10.2) see.
7. Turn on two nuts of fastening of a rack to a rotary fist (are specified by arrows), get bolts and disconnect a rack.
8. Расшплинтуйте also turn away a nut, выпрессуйте a spherical support and a tip of steering draught from fist eyes.
9. Выпрессуйте a nave from the bearing. On a nave there should be one of internal holders of the bearing.
10. Press a holder of the bearing from a nave.
11. Get an external epiploon.
12. Get an internal epiploon.
13. Get from an aperture in a fist under the bearing a lock ring.
14. If ослабла landing of the remained holder get a holder.
15. Выпрессуйте the bearing from a fist оправкой suitable diameter which rests only against an external part of the bearing.
16. At выпрессовке it is necessary to rest a back part of a fist.
17. Выпрессовать the bearing it is possible also blows on the inserted internal holder through tubular оправку.

Installation

PERFORMANCE ORDER
1. Before installation of the new bearing carefully clear an internal surface of a fist.
2. Запрессуйте an external holder of the bearing, resting оправкой only against an external edge. It is forbidden to grease an external part of a holder for simplification запрессовки.
3. Insert into a flute in a fist aperture a lock ring.
4. Put greasing in a cavity of an epiploon and it is cautious запрессуйте an epiploon from lateral aspect of a rotary fist.
5. Establish a prop of an external part of a fist.
6. Put greasing in an epiploon and запрессуйте an epiploon from the interior of a fist.
7. Reliably having rested an internal holder of the bearing, it is cautious запрессуйте a nave in a fist.
8. Check up freedom of rotation of a nave.
9. Attach полуось and tighten a nut with the set moment.
10. Dress a disk and a brake support.
11. Attach a spherical support of the bottom lever, wrap a new nut and tighten with the set moment.
12. Зашплинтуйте a nut new шплинтом.
13. Attach a rack, having replaced bolts and nuts.
14. Tighten bolts and nuts with the set moment.
15. Attach steering draught, having replaced a nut and шплинт.
16. Establish a wheel and lower the car.


12.1. Specifications

12.3. A rack of a forward suspension bracket