Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
2.1. Specifications
2.2. Service through each 15000 km or 6 months
2.2.1. Replacement of oil and the oil filter
2.2.2. Check of turns of idling and quality of a mix
2.2.3. Replacement of spark plugs by cars without neutralizer
2.2.4. Check of level of a liquid of a hydrodrive of brakes
2.2.5. Check of level of a liquid in the wheel hydraulic booster
2.2.6. Check of level of a liquid in automatic transmission
2.2.7. Check of leaks and a condition of hoses
2.2.8. Check of level of oil in a manual transmission
2.2.9. Condition check колодок forward and back brakes.
2.2.10. Check and adjustment of a manual brake
2.2.11. Check and adjustment of a drive of coupling
2.3. Service through each 30000 km or 12 months
2.4. Service through each 60000 km or 2 years
2.5. Service through each 60000 km or 12 months
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



2-2-3-zamena-svechejj-zazhiganiya-na-avtomobilyakh-bez-nejjtralizatora.html

2.2.3. Replacement of spark plugs by cars without neutralizer

Profitability and traction qualities of the engine in many respects depend on a condition of spark plugs. The type of candles should correspond recommended, in this case care of candles during the period between their replacement as a rule is not required. Clearing of candles is required seldom, and in the absence of the necessary equipment to clear candles does not follow in order to avoid breakage of electrodes.

PERFORMANCE ORDER
1. If on tips of high-voltage wires there are no the labels specifying in an accessory to the given cylinder put labels from 1 to 4 (1st cylinder is located from outside mechanism chains timing). Disconnect wires, keeping for a tip, instead of for a wire.
2. Before turning out candles it is recommended to remove a dirt from deepenings near to candles by means of a pure brush, a vacuum cleaner or compressed air to avoid dirt hit in cylinders.
3. Turn out candles a special candle key, or накидным a key, or a face head with the extension piece. At отворачивании keep a head strictly in a direction of an axis of a candle, otherwise at a head warp breakage of a porcelain insulator is possible. Candles are recommended to be checked by the following technique.
4. On appearance of a candle it is possible to define an engine condition precisely enough. If the skirt of an insulator of a candle pure and white colour and on it is absent a touch it specifies in the impoverished gas mixture or that the candle insulator it it it was heated (the heated candle badly takes away heat from an electrode, and on a cold candle heat it is taken away quickly).
5. If the insulator and a candle electrode are covered by firm adjournment of black colour it testifies to the reenriched gas mixture. Massive oily adjournment specify that the engine is worn out or worked on the reenriched mix.
6. If the insulator skirt is pruinose sand or ryzhevato-brown colour the engine is in good repair and mix structure are optimum
7. The backlash between electrodes of candles has special value, – at increase or reduction of a backlash against norm the size of a spark interval and igniting ability of a spark will essentially vary. It is necessary to establish an optimum backlash between the electrodes, specified in subsection 2.1.
8. Before adjustment measure a backlash щупом and turn in (or unbend) an external electrode before reception of the necessary backlash. It is forbidden to turn in the central electrode, as the candle insulator can burst that will entail serious breakages.
9. For measurement and backlash adjustment on sale there is a special adaptation.
10. Before installation of candles be convinced of durability of carving conclusions of the central electrode and in cleanliness of a carving of candles and an insulator, using a piece of a rubber hose to wrap candles without a warp.
11. Remove a rubber hose and tighten a candle динамометрическим a key with a special face head. Wrap other candles.
12. Connect high-voltage wires in a former order, establish all removed details.


2.2.2. Check of turns of idling and quality of a mix

2.2.4. Check of level of a liquid of a hydrodrive of brakes