Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
2.1. Specifications
2.2. Service through each 15000 km or 6 months
2.3. Service through each 30000 km or 12 months
2.3.1. Check and replacement of belts of a drive of auxiliary units
2.3.1.1. A belt of the compressor of the conditioner
2.3.1.2. A belt of a drive of the pump of the hydraulic booster
2.3.1.3. A belt of a drive of the generator
2.3.2. Replacement of the fuel filter
2.3.3. Replacement of spark plugs (а/м without каталического neutralizer)
2.3.4. Work check заслонки a temperature regulator of the air filter
2.3.5. Check of system of decrease in toxicity of the fulfilled gases
2.3.6. Check of the gauge of exhaust gases
2.3.7. Replacement of a brake liquid
2.3.8. Suspension bracket and steering check
2.3.9. Check of covers of semiaxes
2.3.10. Exhaust system check
2.3.11. Check of corners of installation of wheels
2.3.12. Shift of wheels
2.3.13. Check колодок back drum-type brakes
2.3.14. Check of a condition of seat belts
2.3.15. Greasing of door loops and locks
2.3.16. Car check in road conditions
2.4. Service through each 60000 km or 2 years
2.5. Service through each 60000 km or 12 months
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



2-3-1-1-remen-kompressora-kondicionera.html

2.3.1.1. A belt of the compressor of the conditioner

Removal

PERFORMANCE ORDER
1. Working under a forward part of the car, turn away screws and remove a plastic guard under a wing to get access to a pulley коленвала. For expansion of working space it is possible to remove in addition also an engine mudguard, having turned away screws.
2. Turn коленвал the face head dressed on a bolt of a pulley so that it was possible to examine belts (or a belt) on all length. Check up presence on belts of cracks, traces подгорания or mechanical damages. Check up also presence on a belt of glossy sites and stratifications. At detection of damages or wear tracks a belt replace.
3. Disconnect the battery from weight.
4. Release a fastening nut натяжителя a belt to the engine.
5. Turn away an adjusting bolt, displace a roller натяжителя from a belt, before its full easing and remove a belt from pulleys.

Installation

PERFORMANCE ORDER
1. If the new belt be preliminary convinced is established that its type in accuracy corresponds to type of the replaced.
2. Dress a belt on pulleys.
3. Rotating an adjusting bolt, pull a belt.

Tension adjustment
PERFORMANCE ORDER
1. Working under a forward part of the car, turn away screws and remove a plastic guard under a wing to get access to a pulley коленвала. For expansion of working space it is possible to remove in addition also an engine mudguard, having turned away screws.
2. Turn коленвал the face head dressed on a bolt of a pulley so that it was possible to examine belts (or a belt) on all length. Check up presence on belts of cracks, traces подгорания or mechanical damages. Check up also presence on a belt of glossy sites and stratifications. At detection of damages or wear tracks a belt replace.
3. The correct tension of a belt allows to prolong term of its service. Avoid an excessive tension of a belt, deterioration of bearings of the generator otherwise amplifies.
4. The belt tension is checked on deflection size in the middle between two pulleys in the top part of a contour of a belt drive. Under the influence of the set effort the belt deflection should be within norm.
5. For tension adjustment release a roller nut натяжителя and rotate an adjusting bolt before reception of a normal tension. After adjustment turn коленвал on two turns and again check up a belt tension.
6. Upon termination of tighten a roller nut натяжителя with the set moment and connect the battery to weight.
7. Establish the removed guards, a wheel and lower the car.



2.3.1. Check and replacement of belts of a drive of auxiliary units

2.3.1.2. A belt of a drive of the pump of the hydraulic booster