Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
2.1. Specifications
2.2. Service through each 15000 km or 6 months
2.3. Service through each 30000 km or 12 months
2.3.1. Check and replacement of belts of a drive of auxiliary units
2.3.1.1. A belt of the compressor of the conditioner
2.3.1.2. A belt of a drive of the pump of the hydraulic booster
2.3.1.3. A belt of a drive of the generator
2.3.2. Replacement of the fuel filter
2.3.3. Replacement of spark plugs (а/м without каталического neutralizer)
2.3.4. Work check заслонки a temperature regulator of the air filter
2.3.5. Check of system of decrease in toxicity of the fulfilled gases
2.3.6. Check of the gauge of exhaust gases
2.3.7. Replacement of a brake liquid
2.3.8. Suspension bracket and steering check
2.3.9. Check of covers of semiaxes
2.3.10. Exhaust system check
2.3.11. Check of corners of installation of wheels
2.3.12. Shift of wheels
2.3.13. Check колодок back drum-type brakes
2.3.14. Check of a condition of seat belts
2.3.15. Greasing of door loops and locks
2.3.16. Car check in road conditions
2.4. Service through each 60000 km or 2 years
2.5. Service through each 60000 km or 12 months
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



2-3-1-3-remen-privoda-generatora.html

2.3.1.3. A belt of a drive of the generator

Removal

PERFORMANCE ORDER
1. Working under a forward part of the car, turn away screws and remove a plastic guard under a wing to get access to a pulley коленвала. For expansion of working space it is possible to remove in addition also an engine mudguard, having turned away screws.
2. Turn коленвал the face head dressed on a bolt of a pulley so that it was possible to examine belts (or a belt) on all length. Check up presence on belts of cracks, traces подгорания or mechanical damages. Check up also presence on a belt of glossy sites and stratifications. At detection of damages or wear tracks a belt replace.
3. Disconnect the battery from weight. On cars with the conditioner remove a belt of a drive of the compressor of the conditioner (subsection 2.3.1.1 see). On cars with the wheel hydraulic booster remove a belt of a drive of the pump of the hydraulic booster (subsection 2.3.1.2 see).
4. Release the top and bottom nuts (or bolts) generator fastenings.
5. Rotating an adjusting bolt, ослабьте a belt, remove a belt from pulleys.

Installation

PERFORMANCE ORDER
1. If the new belt be preliminary convinced is established that its type in accuracy corresponds to type of the replaced.
2. Dress a belt on pulleys.
3. Rotating an adjusting bolt, pull a belt.
4. Establish and adjust belts of a drive of the compressor of the conditioner and the hydraulic booster.

Tension adjustment

PERFORMANCE ORDER
1. Working under a forward part of the car, turn away screws and remove a plastic guard under a wing to get access to a pulley коленвала. For expansion of working space it is possible to remove in addition also an engine mudguard, having turned away screws.
2. Turn коленвал the face head dressed on a bolt of a pulley so that it was possible to examine belts (or a belt) on all length. Check up presence on belts of cracks, traces подгорания or mechanical damages. Check up also presence on a belt of glossy sites and stratifications. At detection of damages or wear tracks a belt replace.
3. Avoid an excessive tension of a belt, deterioration of bearings of the generator otherwise amplifies.
4. The belt tension is checked on deflection size in the middle between two pulleys in the top part of a contour of a belt drive. Under the influence of the set effort the belt deflection should be within norm (subsection 2.1 see).
5. At tension adjustment the top nut (or a bolt) the generator should be slightly tightened, and the bottom nut (or a bolt) is released. Rotating an adjusting bolt, adjust a tension. After adjustment turn коленвал on two turns and again check up a belt tension. Tighten all nuts (and bolts) generator fastenings.
6. Establish the removed guards, a wheel and lower the car.


2.3.1.2. A belt of a drive of the pump of the hydraulic booster

2.3.2. Replacement of the fuel filter