Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
2.1. Specifications
2.2. Service through each 15000 km or 6 months
2.3. Service through each 30000 km or 12 months
2.3.1. Check and replacement of belts of a drive of auxiliary units
2.3.2. Replacement of the fuel filter
2.3.3. Replacement of spark plugs (а/м without каталического neutralizer)
2.3.4. Work check заслонки a temperature regulator of the air filter
2.3.5. Check of system of decrease in toxicity of the fulfilled gases
2.3.6. Check of the gauge of exhaust gases
2.3.7. Replacement of a brake liquid
2.3.8. Suspension bracket and steering check
2.3.9. Check of covers of semiaxes
2.3.10. Exhaust system check
2.3.11. Check of corners of installation of wheels
2.3.12. Shift of wheels
2.3.13. Check колодок back drum-type brakes
2.3.14. Check of a condition of seat belts
2.3.15. Greasing of door loops and locks
2.3.16. Car check in road conditions
2.4. Service through each 60000 km or 2 years
2.5. Service through each 60000 km or 12 months
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



2-3-11-proverka-uglov-ustanovki-koles.html

2.3.11. Check of corners of installation of wheels

Definitions

PERFORMANCE ORDER
1. Stability of the car at turn and optimum position of forward wheels in space are defined by four basic corners which are expressed in degrees (except for a corner of a convergence which is expressed by the dimensional size received directly from measurements).
2. Disorder of wheels is a corner formed by a plane of a wheel and the vertical line spent through the centre of a wheel and a platform of contact of the tyre with a road covering if to look in front or behind the car. At "positive" disorder the top part of a wheel is displaced from a vertical aside from the car, at "negative" disorder the top part of a wheel is displaced from a vertical towards the car.
3. Disorder of wheels is not regulated and given only for the inquiry. It is possible to measure this corner by means of the special adaptation. If the corner of disorder of wheels differs from standard it is necessary to hand over the car on a car repair shop for check by the skilled personnel as a unique cause of infringement of disorder is deterioration or damage of details of a suspension bracket or a body.
4. The corner of a longitudinal inclination of an axis of turn is a corner formed by an axis of turn of a wheel and a vertical spent through the centre of a wheel and a platform of contact of the tyre with a road covering if to look sideways from the car. At "a positive" longitudinal inclination of an axis of turn the turn axis is inclined in such a manner that the axis line passes before a vertical spent from the centre of a wheel if to look on a car course.
5. At "a negative" inclination the turn axis passes behind a vertical spent from the centre of a wheel if to look on a car course.
6. The corner of a longitudinal inclination of an axis of turn is not regulated and given only for the inquiry. It is possible to measure this corner at the special stand. If the corner of a longitudinal inclination of an axis of turn differs from standard it is necessary to hand over the car on a car repair shop for check as deterioration or damage of details of a suspension bracket or a body can be a disorder cause of infringement only.
7. The corner of a cross-section inclination of an axis of turn (it is usually designated SAI) is the corner formed between an axis of turn and a line, spent through the centre of a wheel and a platform of contact of the tyre with a road covering if to look behind or in front of the car. This corner is provided with a suspension bracket design.
8. The convergence of wheels is a corner between an axis of the car and a line spent through the centre of a wheel in a horizontal plane. Wheels "converge", if are turned to each other and "disperse", if are turned every which way on a car course.
9. The convergence of forward wheels is regulated by rotation of tips of steering draughts at which the total length of both draughts changes.
10. The convergence of back wheels is regulated by rotation of clowns on bolts of fastening of cross-section levers of a back suspension bracket to a body.

Corners of installation of wheels – check

For check of corners of installation of wheels application of the special equipment and sufficient experience are required, therefore, this kind of service is expedient for carrying out on a car repair shop.

Balancing of wheels

This kind of service is expedient for carrying out in service of car-care centre or in a specialised workshop.



2.3.10. Exhaust system check

2.3.12. Shift of wheels