Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
2.1. Specifications
2.2. Service through each 15000 km or 6 months
2.3. Service through each 30000 km or 12 months
2.4. Service through each 60000 km or 2 years
2.4.1. Replacement of the air filter
2.4.2. Check of system of ignition
2.4.3. Replacement of the filter of ventilation картера
2.4.4. Check of a hose and the control vacuum amplifier
2.4.5. Replacement of a cooling liquid
2.4.6. Replacement трансмиссионной liquids in automatic transmission
2.5. Service through each 60000 km or 12 months
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



2-4-2-proverka-sistemy-zazhiganiya.html

2.4.2. Check of system of ignition


The prevention

The pressure developed by system of ignition, much more exceeds pressure from other systems of the car. At performance of works with the included ignition it is necessary to observe extra care. To persons at whom вживлен кардиостимулятор, it is forbidden to work near to chains and devices of system of ignition, and also the control and measuring equipment.


The condition and serviceability of devices and devices of system of ignition should be checked, being guided by the description in corresponding subsections.

The general check

PERFORMANCE ORDER
1. High-voltage wires of spark plugs it is necessary to check every time at replacement of candles. If necessary uncover the ignition distributor.
2. Before a detachment of high-voltage wires be convinced that on them there is a numbering specifying in an accessory of a wire to the given cylinder.
3. Remove wires, keeping for tips instead of for a wire, in order to avoid a separation of a spending vein of a wire from a tip
4. Check up presence of corrosion in tips, corrosion is usually found out in the form of a white powder. Again put a tip into place, and be convinced of reliability of its fastening on a candle. If contact unreliable remove a tip and cautiously turn in an adapter in a tip, having achieved dense облегания a candle conclusion.
5. Wipe dry all wire. It is forbidden to bend excessively a wire or to extend.
6. Disconnect the opposite end of a wire from the ignition distributor, having pulled for a tip. Check up corrosion presence in a tip from outside the distributor and reliability of fastening of a wire, having arrived just as and at tip check from outside candles. Measure resistance of a wire, having connected an ohmmeter to a conclusion from outside candles and to a segment platform in a distributor cover. After check put a wire into place.
7. Check up other wires in the same order.
8. If it is required to replace high-voltage wires get the complete set of the new wires which type corresponds to the car and the engine.
9. Turn away screws of fastening of a cover of the distributor. Uncover also a sealant. Wipe a cover absolutely and check up presence inside and outside of a cover of cracks, traces of superficial breakdown (the thin charred paths), deterioration and подгорания contacts.
10. Check up deterioration of pieces of coal, freedom of their moving under the influence of springs and reliability of contact with бегунком. Check up also a condition of a sealant of a cover of the distributor, at detection of damages a sealant replace. Turn away screws and remove from the distributor platen бегунок, check up a condition бегунка.
11. At replacement of high-voltage wires it is recommended to replace бегунок and a distributor cover. At replacement disconnect from an old cover a wire and insert into a new cover on the same place from which it has been taken on an old cover. It is forbidden to get simultaneously from an old cover two and more wires, their wrong installation and infringement of an operating procedure of cylinders otherwise is possible.
12. Reliably запрессуйте бегунок on the distributor platen, tighten the screw. Lay a lining and establish a distributor cover, tighten screws. Establish a cap.
13. Even if the condition of the distributor does not inspire any doubts, on some engines the complicated start-up that is caused by moisture hit in a detail of system of ignition can be observed sometimes nevertheless. In this case effectual measures is application of the aerosols providing dispersion of a moisture, or drawing of a water-repellent tight covering.

Check and installation of the moment of ignition

The procedure for test of the moment of ignition see in subsection 7.7.7.



2.4.1. Replacement of the air filter

2.4.3. Replacement of the filter of ventilation картера