Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
3.1. The petrol engine in volume of 1,4 and 1,6 litres
3.1.1. Kinds of repair of the engine without dismantle from the car
3.1.1.1. Specifications
3.1.1.2. A compression
3.1.1.3. An order of installation of the piston of 1st cylinder in ВМТ a compression step
3.1.1.4. A cover of a head of the block of cylinders
3.1.1.5. A pulley коленвала
3.1.1.6. A cover of a chain drive of cam-shafts
3.1.1.7. Chains of a drive of cam-shafts
3.1.1.8. Натяжители and успокоители chains, drive asterisks
3.1.1.9. Backlashes in the mechanism of a drive of valves
3.1.1.10. Cam-shafts and pushers
3.1.1.11. A head of the block of cylinders
3.1.1.12. The oil pallet
3.1.1.13. The oil pump
3.1.1.14. Epiploons коленвала
3.1.1.15. A flywheel
3.1.1.16. Engine mount details
3.1.2. Dismantle and engine major repairs
3.2. The petrol engine in volume of 2,0 litres
3.3. The diesel engine
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



3-1-1-3-poryadok-ustanovki-porshnya-1-go-cilindra-v-vmt-takta-szhatiya.html

3.1.1.3. An order of installation of the piston of 1st cylinder in ВМТ a compression step

PERFORMANCE ORDER
1. Disconnect the battery from weight and turn out spark plugs (cм. Subsection 2.2.3).
2. On a wire from a candle of 1st cylinder find a corresponding conclusion to a cover of the distributor of ignition and small put a label on the case of the distributor or on inflow of the block of cylinders opposite to which there is a conclusion of 1st cylinder. Unhook latches of a cover of the distributor (if are provided), turn away screws of fastening and uncover together with a lining.
3. Put the car on a manual brake and translate the check point lever in neutral position. Lift a forward part of the car and establish on supports. Remove the right wheel.
4. Turn away screws and remove a plastic guard under a wing (it is specified by an arrow).
5. Provide access to a pulley bolt коленвала.
6. On a pulley wreath there are adjusting risks which are combined with an index scale on a cover of chains of a drive of a cam-shaft. Risks are put with an interval in 5 . The first risk is located in 20 to ВМТ, and last – in 5 after ВМТ. The risk, corresponding ВМТ, it is noted by a yellow paint.
7. Turn коленвал for a head of a bolt of a pulley clockwise (if to look on the right side of the car) before combination risks ВМТ on a pulley wreath коленвала with the index on a cover.
8. At such position коленвала pistons of 1st and 4th cylinders are in ВМТ, and only one of them is in ВМТ a compression step. If бегунок the distributor specifies in a label of a conclusion of 1st cylinder 1st cylinder is established in ВМТ a compression step. If бегунок the distributor specifies a conclusion of 4th cylinder turn коленвал on 1 turn (360 ) clockwise, before position when бегунок specifies in a label of 1st cylinder. Now the piston of 1st cylinder will be exposed in ВМТ a compression step.
9. Turning коленвал on 180 clockwise concerning position ВМТ of 1st cylinder, it is possible to expose in ВМТ the piston of each cylinder according to an engine operating procedure.


3.1.1.2. A compression

3.1.1.4. A cover of a head of the block of cylinders