Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
3.1. The petrol engine in volume of 1,4 and 1,6 litres
3.1.1. Kinds of repair of the engine without dismantle from the car
3.1.1.1. Specifications
3.1.1.2. A compression
3.1.1.3. An order of installation of the piston of 1st cylinder in ВМТ a compression step
3.1.1.4. A cover of a head of the block of cylinders
3.1.1.5. A pulley коленвала
3.1.1.6. A cover of a chain drive of cam-shafts
3.1.1.7. Chains of a drive of cam-shafts
3.1.1.8. Натяжители and успокоители chains, drive asterisks
3.1.1.9. Backlashes in the mechanism of a drive of valves
3.1.1.10. Cam-shafts and pushers
3.1.1.11. A head of the block of cylinders
3.1.1.12. The oil pallet
3.1.1.13. The oil pump
3.1.1.14. Epiploons коленвала
3.1.1.15. A flywheel
3.1.1.16. Engine mount details
3.1.2. Dismantle and engine major repairs
3.2. The petrol engine in volume of 2,0 litres
3.3. The diesel engine
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



3-1-1-4-kryshka-golovki-bloka-cilindrov.html

3.1.1.4. A cover of a head of the block of cylinders


Sequence of an inhaling of bolts of a cover of a head of cylinders

Removal

PERFORMANCE ORDER
1. Disconnect from wire candles, get wires from скоб on a cover of a head of cylinders.
2. Ослабьте collars also disconnect hoses отсоса внутрикартерных gases in on a cover of a head of cylinders.
3. As it should be the return specified in fig. Sequence of an inhaling of bolts of a cover of a head of cylinders, turn away bolts of fastening of a cover of a head of cylinders, get bolts and washers.
4. Lift a cover of a head of cylinders, get a rubber lining from a flute in a cover and sealing rings of candles from apertures under candles. On engines of early release also get rubber заглушки, inserted into semicircular deepenings in the right wall of a head of cylinders. On engines of later release these заглушки are executed at the same time with a lining of a cover of a head of cylinders.
5. Check up a condition of all rubber sealants of a cover, if necessary replace.

Installation

PERFORMANCE ORDER
1. Carefully clear condensed surfaces of a cover and a head of cylinders, remove oil traces.
2. Put hermetic on semicircular samples of a head of cylinders. On engines of early release lay in both samples semicircular заглушки so that the flat part заглушек was заподлицо with a plane of a head of cylinders.
3. Lay a lining in a flute on a cover, having tracked correctness of its position on all length.
4. Establish sealing rings of spark plugs. If necessary fix уплотнители, having greased with a thin layer of hermetic.
5. Put hermetic on a lining approximately in 1 sm on either side of from edges of semicircular sample under a cover of a back basic neck of a cam-shaft.
6. Cautiously establish a cover of a head of cylinders into place, thus displacement of rubber sealants of a cover is not supposed.
7. Be convinced of correctness of installation of a cover, wrap bolts with washers. Tighten cover bolts in the specified sequence with the set moment.
8. Attach to a cover hoses.
9. Attach wires to spark plugs and insert wires in скобы.


3.1.1.3. An order of installation of the piston of 1st cylinder in ВМТ a compression step

3.1.1.5. A pulley коленвала