Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
3.1. The petrol engine in volume of 1,4 and 1,6 litres
3.1.1. Kinds of repair of the engine without dismantle from the car
3.1.2. Dismantle and engine major repairs
3.1.2.1. Specifications
3.1.2.2. Engine major repairs
3.1.2.3. Diagnostics of the engine by means of the vacuum gauge
3.1.2.4. The power unit from a manual transmission
3.1.2.5. The power unit with automatic transmission
3.1.2.6. A head of the block of cylinders
3.1.2.7. A head of cylinders and valves
3.1.2.8. Pistons and rods
3.1.2.9. Коленвал
3.1.2.10. The block of cylinders
3.1.2.11. Shatunno-piston group
3.1.2.12. Radical and шатунные bearings
3.1.2.13. Piston rings
3.1.2.14. Start-up of the engine after major repairs
3.2. The petrol engine in volume of 2,0 litres
3.3. The diesel engine
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



3-1-2-12-korennye-i-shatunnye-podshipniki.html

3.1.2.12. Radical and шатунные bearings


Kinds of deterioration radical and шатунных bearings

A.Tsarapiny because of dirt hit
V.Nedostatochnaja greasing, a local wipe
S.Nepravilnaja installation of bearings
F. Fatigue deterioration
D. Конусность necks, a wipe of a covering of the bearing from all surface on length of the bearing
E.Obrazovanie of a fillet on a bearing edge

Check

PERFORMANCE ORDER
1. The bearings which were in operation should be stored in a place of their installation for careful check as wear tracks on these details allow to restore the general condition of the engine. Loose leaves of bearings are subdivided into dimensional groups on a thickness specified by colour marks.
2. Sources of rupture of bearings of a cranked shaft are insufficient greasing, presence of a dirt and extraneous particles, an overload of the engine and corrosion. Irrespective of the reason which have caused destruction of bearings, it should be eliminated before definitive assemblage of the engine.
3. Get bearings from the block of cylinders and lay out loose leaves on a pure surface as their installation.
4. For the prevention of the accelerated deterioration because of pollution support cleanliness at engine assemblage. While in service it is recommended to a thicket to change oil and filters.
5. At insufficient greasing, there is a material of a covering of the bearing is wiped from a steel basis, the bearing is painted from an overheat (the bluish shade is observed).
6. At movement in heavy modes for the engine (with completely open throttle заслонкой, or with small speed on the raised transfer) occurs a separation of a covering of the bearing from a steel basis in the form of small particles, bearings are exposed to fatigue deterioration.
7. Frequent trips on small distances can be at the bottom of corrosion deterioration of bearings as because of insufficient warming up have not time to leave сконденсированная a moisture.
8. Wrong installation of bearings at assemblage also leads to their premature deterioration. If the backlash in bearings is less than norm their greasing is complicated that leads to deterioration as well as owing to "oil to starvation".
9. At assemblage do not touch with fingers loose leaf surfaces.
10. Loose leaves radical and шатунных bearings at major repairs are subject to obligatory replacement.


3.1.2.11.2. Installation and check of backlashes in шатунных bearings

3.1.2.13. Piston rings