Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
3.1. The petrol engine in volume of 1,4 and 1,6 litres
3.1.1. Kinds of repair of the engine without dismantle from the car
3.1.2. Dismantle and engine major repairs
3.1.2.1. Specifications
3.1.2.2. Engine major repairs
3.1.2.2.1. An order of dismantling and engine assemblage
3.1.2.3. Diagnostics of the engine by means of the vacuum gauge
3.1.2.4. The power unit from a manual transmission
3.1.2.5. The power unit with automatic transmission
3.1.2.6. A head of the block of cylinders
3.1.2.7. A head of cylinders and valves
3.1.2.8. Pistons and rods
3.1.2.9. Коленвал
3.1.2.10. The block of cylinders
3.1.2.11. Shatunno-piston group
3.1.2.12. Radical and шатунные bearings
3.1.2.13. Piston rings
3.1.2.14. Start-up of the engine after major repairs
3.2. The petrol engine in volume of 2,0 litres
3.3. The diesel engine
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



3-1-2-2-1-poryadok-razborki-i-sborki-dvigatelya.html

3.1.2.2.1. An order of dismantling and engine assemblage


The block of cylinders, коленвал and shatunno-piston group

1. A flywheel bolt
2. A flywheel
3. An assembly plate
4. An epiploon
5. The holder of an epiploon
6. The block of cylinders
7. Directing pins and linings
8. Piston rings
9. Lock rings
10. A porshnevyj finger
11. The piston
12. A rod
13. Radical loose leaves and persistent half rings
14. Коленвал
15. A rod cover
16. Covers of radical bearings
17. The oil pallet
18. A drain stopper

PERFORMANCE ORDER
1. It is recommended to assort the engine at the special stand.
2. If the stand is not present, fix the engine on an equal platform.
3. If the restored engine it is necessary to remove all hinged units is got, and to establish them subsequently precisely in the same order as well as at independent major repairs. To such units (fig. the Block of cylinders see, коленвал and shatunno-piston group) concern:

  – The generator and arms of the pump of the hydraulic booster and (or) the conditioner compressor (depending on a complete set);
  – The distributor of ignition, a candle and high-voltage wires;
  – The pump of a cooling liquid and thermostat and radiator hoses;
  – Details of the carburettor or system of injection of fuel;
  – All gauges and electromagnetic valves with conducting;
  – Soaking up and final collectors;
  – The fuel pump – for carburettor engines;
  – Engine mount details;
  – A flywheel / a leading disk of the hydrotransformer.

The prevention

Before removal of hinged units put labels on linings, epiploons and other details to facilitate assemblage.


4. If the block of cylinders of an incomplete complete set (i.e. the block of cylinders with picked up both established krivoshipno-shatunnym the mechanism and piston group) it is necessary to remove also a head of the block of cylinders, the oil pallet, the oil pump and chains is established.

5. If it is planned to carry out major repairs with full dismantling the engine should be disassembled completely a following order:

  – Soaking up and final collectors;
  – The oil pallet;
  – Chains and asterisks;
  – A head of the block of cylinders;
  – A flywheel;
  – Shatunno-piston group;
  – коленвал.

6. Before dismantling prepare the necessary equipment and tools.


3.1.2.2. Engine major repairs

3.1.2.3. Diagnostics of the engine by means of the vacuum gauge