Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
3.1. The petrol engine in volume of 1,4 and 1,6 litres
3.2. The petrol engine in volume of 2,0 litres
3.2.1. Kinds of repair of the engine without dismantle from the car
3.2.1.1. Specifications
3.2.1.2. Compression check in engine cylinders
3.2.1.3. An order of installation of the piston of 1st cylinder in ВМТ a compression step
3.2.1.4. A cover of a head of the block of cylinders
3.2.1.5. A pulley коленвала
3.2.1.6. A cover of a chain drive of cam-shafts
3.2.1.7. A chain of a drive of cam-shafts
3.2.1.8. Натяжитель chains, успокоитель and drive asterisks
3.2.1.9. Cam-shafts
3.2.1.10. Levers of a drive of valves and hydraulic regulators
3.2.1.11. A head of cylinders
3.2.1.12. The oil pallet
3.2.1.13. The oil pump
3.2.1.14. Маслоохладитель
3.2.1.15. Epiploons коленвала
3.2.1.16. A flywheel (or a leading disk of the hydrotransformer)
3.2.1.17. Details of a suspension bracket of the power unit
3.2.2. Dismantle and engine major repairs
3.3. The diesel engine
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



3-2-1-12-maslyanyjj-poddon.html

3.2.1.12. The oil pallet


Sequence of an inhaling of nuts and bolts of the aluminium oil pallet


Removal

PERFORMANCE ORDER
1. Put the car on a manual brake, then lift a forward part of the car and establish on supports. Disconnect the battery from weight.
2. Turn away screws and remove a plastic casing under the engine.
3. Merge oil from the engine. After an oil drain clear a drain stopper, turn and tighten with the set moment. If works are carried out at approach of term of replacement of oil and the filter it is recommended to replace the filter also. After assemblage in the engine fill in fresh oil.
4. Being guided by the description in subsection 6.1.13, disconnect a reception pipe of the muffler from a final collector.
5. In sequence of return specified in fig. Sequence of an inhaling of nuts and bolts of the aluminium oil pallet, turn away all bolts of fastening of the small pallet stamped from a steel to the basis of the main pallet cast from an aluminium alloy. With palm blows open consolidation of the small pallet and get it from under the car.
6. Turn away bolts and remove маслоотражательную a plate from the basis of the aluminium pallet.
7. Slightly raise картер transmissions by a jack, having laid a board that the jack has apprehended unit weight. It is possible to hang out also the engine on a traverse or on тали.
8. On cars from a manual transmission with a marker mark a bolt arrangement on an arm of a forward support. On these labels the bolt will be established at assemblage. Release and turn on a nut, then get a coupling bolt of a support.
9. On all cars release and turn away a nut of a coupling bolt and get a bolt from a back support of the power unit.
10. Release and turn on four bolts of fastening of the central longeron to a body, remove a longeron in gathering and get from under the car. Remove a restrictive ring which is established between a back support and an arm.
11. On the cars equipped with the conditioner, release and turn away bolts of fastening of the bottom arm of the compressor of the conditioner to the aluminium pallet.
The prevention

It is not necessary to remove the compressor.


12. Turn away two bolts of an overlay of the pallet.
13. Remove an overlay then access to two nuts of fastening of the pallet will be provided.
14. In sequence of return specified in drawing, turn away a nut and bolts of fastening of the aluminium pallet to the basis of the block of cylinders.
15. Turn away two bolts of fastening (1) фланцевой parts of the oil pallet to картеру transmissions. These bolts should be screwed in nearby carving apertures (2), and to use them for removal of the oil pallet from the block of cylinders by заворачивания. Wrap bolts against the stop in a demountable plane of the block of cylinders, then serially tighten bolts, gradually increasing effort, providing with that uniform without warps removal of the pallet from the basis of the block of cylinders.
16. Remove the aluminium pallet and turn out the bolts used for branch of the pallet from the block of cylinders.

The prevention

On the cars equipped with automatic transmission, it can be necessary for pallet removal to disconnect a cable of the lever of the selector from transmission.


17. While the pallet is removed turn away two bolts and remove from a skeleton of covers of radical bearings коленвала маслоприемник with the filter of rough clearing and маслоотражательную a plate. Remove the ring lining established between the filter маслоприемника and a cover of a chain of the mechanism timing. Wash out the filter of rough clearing in solvent. Check up presence of contaminations or ruptures in a filter grid маслоприемника. At any signs of damages replace маслоприемник in gathering with the filter of rough clearing.
18. Check up presence of signs of damages on rubber plugs of the central longeron, in need of the plug replace.

Installation

PERFORMANCE ORDER
1. Clear of the consolidation rests demountable planes of both pallets and the block of cylinders, then wipe absolutely pallets and internal surfaces of the engine.
2. In a flute маслоприемника lay a new ring lining and establish маслоприемник on the basis of a cover of a chain drive. Reliably tighten fastening bolts маслоприемника. Establish маслоотражательную a plate on inflow in the bottom part картера коленвала, reliably tighten fastening bolts.
3. Be convinced that demountable planes of the pallet and the block of cylinders dry and pure. On a condensed surface of the aluminium pallet put a continuous strip of hermetic. мейте in a kind that round all bolts noted by an asterisk the strip should be outside, and round other bolts – from within.
4. Put the pallet in a place to the block of cylinders. Wrap bolts and nuts, tighten them by hand. Tighten bolts and nuts of the pallet with the set moment, in the sequence specified in fig. Sequence of an inhaling of nuts and bolts of the aluminium oil pallet.
5. Wrap two bolts of fastening of a flange of the pallet to картеру transmissions, reliably them tighten. If necessary connect a cable of the lever of the selector.
6. Establish a cover on фланцевую a pallet part, tighten bolts.
7. On the cars equipped with the conditioner, reliably tighten bolts of fastening of an arm of the compressor.
8. Having convinced available all rubber plugs, establish on an arm of a back support of the power unit a restrictive ring. Establish into place the central longeron, having combined with engine support, wrap bolts with washers. Tighten bolts of fastening of the central longeron with the set moment.
9. On cars from a manual transmission establish in a place a coupling bolt of a forward support of the power unit, wrap a nut. Expose the power unit so that the coupling bolt of a forward support was precisely combined with a label put before dismantling. Then tighten a bolt with the set moment.
10. Insert a coupling bolt of a back support of the power unit and tighten a nut with the set moment.
11. Clean a jack from under картера transmissions.
12. Establish маслоотражательную a plate in the basis of the aluminium pallet, reliably tighten bolts.
13. Check up cleanliness of a demountable surface of the small oil pallet (stamped of a steel). Put on this surface a continuous strip of hermetic.
14. Put hermetic on a flute between apertures on the centre of a demountable surface, and also round an internal edge of each of apertures under bolts.
15. Put the pallet in a place and tighten bolts by hand. Tighten bolts in the specified sequence with the set moment.
16. Establish a reception pipe of the muffler (subsection 6.1.14 see).
17. Establish the bottom guards, tighten fastening screws.
18. Fill in in the engine oil.


3.2.1.11. A head of cylinders

3.2.1.13. The oil pump