Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
3.1. The petrol engine in volume of 1,4 and 1,6 litres
3.2. The petrol engine in volume of 2,0 litres
3.2.1. Kinds of repair of the engine without dismantle from the car
3.2.1.1. Specifications
3.2.1.2. Compression check in engine cylinders
3.2.1.3. An order of installation of the piston of 1st cylinder in ВМТ a compression step
3.2.1.4. A cover of a head of the block of cylinders
3.2.1.5. A pulley коленвала
3.2.1.6. A cover of a chain drive of cam-shafts
3.2.1.7. A chain of a drive of cam-shafts
3.2.1.8. Натяжитель chains, успокоитель and drive asterisks
3.2.1.9. Cam-shafts
3.2.1.10. Levers of a drive of valves and hydraulic regulators
3.2.1.11. A head of cylinders
3.2.1.12. The oil pallet
3.2.1.13. The oil pump
3.2.1.14. Маслоохладитель
3.2.1.15. Epiploons коленвала
3.2.1.16. A flywheel (or a leading disk of the hydrotransformer)
3.2.1.17. Details of a suspension bracket of the power unit
3.2.2. Dismantle and engine major repairs
3.3. The diesel engine
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



3-2-1-15-salniki-kolenvala.html

3.2.1.15. Epiploons коленвала

Removal

PERFORMANCE ORDER
The right epiploon (epiploon of a cover of a chain drive)
1. Remove a pulley коленвала.
2. Cautiously get an epiploon, having hooked its big screw-driver, without having damaged thus a gear wheel of the oil pump and a cover.
3. Clear the case of an epiploon and remove all agnails and sharp edges which can be a principal cause of destruction of an epiploon.
4. Grease working edges of a new epiploon with a thin layer консистентной greasings, cautiously put an epiploon into place so that sponges of working edges have been turned inside, do not damage thus an epiploon edge. Запрессуйте оправкой an epiploon against the stop in a fillet on epiploon periphery. Diameter оправки should be such that at запрессовке оправка rested against external edges of an epiploon. At запрессовке do not damage working edges of an epiploon.
5. Remove the greasing rests, then establish a pulley коленвала.
Back epiploon (epiploon of a flywheel / of a leading disk of the hydrotransformer)
6. Remove a flywheel (or a leading disk of the hydrotransformer).
7. By means of the big screw-driver with a flat edge hook an epiploon for an internal edge and in regular intervals take an epiploon from the block of cylinders, thus do not damage a surface коленвала and the block of cylinders.
8. Clear an installation site of an epiploon and remove all agnails and sharp edges which can cause epiploon destruction first of all.
9. Grease working edges of a new epiploon and a condensed neck коленвала with a thin layer консистентной greasings, it is correct сориентируйте an epiploon rather картера коленвала.
10. Hands, without applying any инструменов, cautiously dress working edges of an epiploon on a condensed neck коленвала. Запрессуйте an epiploon without warps against the stop a fillet on epiploon periphery in кольцеобразный inflow on картере kolenvala/the block of cylinders. It is if necessary supposed to besiege an epiploon in a place easy blows of a hammer with soft the brisk.
11. Remove the greasing rests, then establish a flywheel (or a leading disk of the hydrotransformer).


3.2.1.14. Маслоохладитель

3.2.1.16. A flywheel (or a leading disk of the hydrotransformer)