Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
6.1. Carburettor engines
6.1.1. Specifications
6.1.2. The air filter
6.1.3. A temperature regulator of a stream of air
6.1.4. The fuel pump
6.1.5. The gauge of level of fuel
6.1.6. A fuel tank
6.1.7. A cable of a drive throttle заслонки
6.1.8. A pedal of management throttle заслонкой
6.1.9. Fuel
6.1.10. The carburettor
6.1.11. Gauges and carburettor valves
6.1.12. A soaking up collector
6.1.13. A final collector
6.1.14. An exhaust system
6.2. Engines with system of injection of fuel
6.3. System of a food / of release of the fulfilled gases
6.4. System of decrease in toxicity of the fulfilled gases
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



6-1-11-datchiki-i-klapany-karbyuratora.html

6.1.11. Gauges and carburettor valves

Removal and installation

THE GAUGE OF PRESSURE OF THE PRESSURE

PERFORMANCE ORDER
1. The gauge is mounted on the left cap of a suspension bracket.
2. Disconnect the battery from weight.
3. Turn away screws raise the gauge and disconnect a hose (2) and a socket (1), remove the gauge.
4. Installation is carried out upside-down.

THE TRANSISTOR MODULE

Subsection 7.7.6 see.

THE VALVE OF CORRECTION OF STRUCTURE OF THE MIX

Cм. Subsection 6.1.10.2.

SOLENOIDAL VALVES

Cм. Subsection 6.1.10.2, subitem 18-26.

For workplace expansion remove the air filter.

THE SWITCH THROTTLE ЗАСЛОНКИ

Switch arrangement

The switch throttle заслоки is mounted on the right side of the carburettor.

PERFORMANCE ORDER
1. Turn away two screws.
2. Disconnect wires and remove the switch.
3. At installation adjust the switch.
4. For adjustment warm up and stop the engine, disconnect a socket with switch wires.
5. Connect crosspieces conclusions отсечного the valve and connect an ohmmeter (arrows specify conclusions for ohmmeter connection).
6. Start the engine, finish turns to 2000 rpm and slowly reduce, observing of an ohmmeter which should show the closed chain, and on 1200 rpm – disconnection (works the switch).
7. If necessary adjust the switch подгибанием a uvula.
8. Stop the engine and attach a socket.

THE GAUGE OF TEMPERATURE OF THE COOLING LIQUID

Cм. Subsection 4.6.3.

THE MANAGEMENT BLOCK

The block is mounted or under one of forward seats, or under the central section of the forward panel.

PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Remove a seat or the central section.
3. Turn away screws and remove the block, disconnect conducting.
4. At installation be convinced of correctness of all connections.

THE GAUGE OF ANGLE OF ROTATION КОЛЕНВАЛА

The gauge enters into a design of the distributor of ignition and separately does not act in film.

At an exit from the system gauge all distributor in gathering (subsection 7.7.4 see) varies.

THE GAUGE OF DEENERGIZING OF COUPLING

It is mounted on an arm of the block of pedals.

PERFORMANCE ORDER
1. Disconnect the battery from weight, remove the bottom panel.
2. Disconnect wires, turn away a nut and remove the switch.
3. At installation check up adjustment of a pedal of coupling and adjust the gauge.
4. For adjustment connect to conclusions of the gauge an ohmmeter and adjust position so that at the released pedal there was a rupture, and at slightly pressed – the closed chain.
5. Tighten a nut.

THE GAUGE OF NEUTRAL POSITION OF TRANSMISSION

Cм. Subsection 9.1.4.

THE SWITCH OF CORRECTION OF IDLING AT HYDRAULIC BOOSTER WORK

The switch is built in in a hydraulic booster contour, in the right back part of a motor compartment.

PERFORMANCE ORDER
1. Put wheels in driving position on a straight line and disconnect the battery from weight.
2. Disconnect from the switch a socket.
3. Turn away the switch and muffle an aperture in a tube, get a sealant.
4. At installation replace a sealant.

THE GAUGE OF SPEED OF THE CAR

The gauge is mounted in a speedometer.

6.1.10.2. Diagnostics, dismantling and carburettor adjustment

6.1.12. A soaking up collector