Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
6.1. Carburettor engines
6.2. Engines with system of injection of fuel
6.2.1. Specifications
6.2.2. The air filter
6.2.3. A cable of a drive throttle заслонки
6.2.4. A pedal of management throttle заслонкой
6.2.5. Fuel
6.2.6. System of injection of fuel
6.2.7. Декомпрессия fuel system
6.2.8. The fuel pump
6.2.9. The gauge of level of fuel
6.2.10. A fuel tank
6.2.11. System of injection of fuel
6.2.12. The case throttle заслонки
6.2.13. Units of system of injection of fuel
6.2.14. A soaking up collector
6.2.15. A final collector
6.2.16. An exhaust system
6.3. System of a food / of release of the fulfilled gases
6.4. System of decrease in toxicity of the fulfilled gases
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



6-2-16-vykhlopnaya-sistema.html

6.2.16. An exhaust system

On cars without neutralizer the exhaust system consists of 3 sections – a reception pipe, intermediate section with the resonator and terminal section with the muffler.

On cars with neutralizer the exhaust system consists of 4 sections – the same 3 sections and neutralizer section. On a part of cars it is established two neutralizers, one of which пристыковывается to a collector.

On all length of a pipe of an exhaust system are suspended on rubber support, pipes are connected by flanges.

Removal

Each of sections can be dismantled irrespective of the others. It is possible to remove also at once all system.

PERFORMANCE ORDER
1. Lift the car and establish on supports (or call in on a hole or a platform).
Reception pipe
2. On cars with neutralizer disconnect a socket from the gauge of exhaust gases. Get conducting from скоб.
3. Turn away a fastening nut to a collector and a fastening bolt to an arm, disconnect a pipe from a collector, remove linings.
4. Disassemble фланцевое connection with intermediate section and remove a pipe and a lining.
Neutralizer (on a part of cars)
5. Turn on two nuts and two bolts of fastening of a flange of a reception pipe to neutralizer.
6. Turn away two bolts of fastening of an intermediate pipe to neutralizer.
7. Disconnect neutralizer from a reception pipe and remove.
8. Remove a lining.
Intermediate pipe
9. On cars with neutralizer turn away two bolts of fastening of an intermediate pipe to neutralizer and remove a lining.
10. On cars without neutralizer turn on two nuts and two bolts of fastening, remove springs and disconnect an intermediate pipe from a reception pipe. Remove a lining.
11. On all cars turn away a bolt of a rubber pillow in a back part of an intermediate pipe.
12. Turn away two bolts of fastening of an intermediate pipe to a terminal pipe of the muffler.
13. Remove an intermediate pipe and a lining.
Terminal section of the muffler
14. Turn away two bolts of fastening to an intermediate pipe.
15. Unhook extensions and remove section.
Removal of all system
16. On cars with neutralizer disconnect a socket from the gauge of exhaust gases.
17. Turn away a nut of fastening of a reception pipe to a collector and a fastening bolt to an arm, disconnect a pipe from a collector, remove a lining.
18. Working with the assistant, disconnect system from rubber pillows and remove from the car.
Thermal guards
19. Guards are established on a part of cars between a body and exhaust pipes and fasten nuts, bolts and скобами.

Installation

PERFORMANCE ORDER
1. Installation is carried out upside-down.
2. Before assemblage replace linings and clear demountable surfaces.
3. Check up a condition of pillows, if necessary replace.
4. Be convinced that between pipes, sufficient gleams are available the bottom and details of suspension brackets.


6.2.15. A final collector

6.3. System of a food / of release of the fulfilled gases