Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
6.1. Carburettor engines
6.2. Engines with system of injection of fuel
6.3. System of a food / of release of the fulfilled gases
6.3.1. Models with one-dot electronic injection of fuel
6.3.1.1. Technical characteristics
6.3.1.2. The air filter
6.3.1.3. An accelerator rope
6.3.1.4. An accelerator pedal
6.3.1.5. The gasoline which is not containing тетраэтилсвинца
6.3.1.6. System of injection of fuel
6.3.1.7. Fuel system
6.3.1.8. The fuel pump
6.3.1.9. The gauge of level of fuel
6.3.1.10. A fuel tank
6.3.1.11. The case throttle заслонки
6.3.1.12. System of injection of fuel / of ignition
6.3.1.13. Elements of system of injection of fuel
6.3.1.14. An inlet collector
6.3.2. Models with multidot electronic injection of fuel
6.4. System of decrease in toxicity of the fulfilled gases
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



6-3-1-11-korpus-drosselnojj-zaslonki.html

6.3.1.11. The case throttle заслонки


The prevention

Look safety measures in subsection 6.3.1 before the work beginning.


Removal
PERFORMANCE ORDER
1. Disconnect a wire of the negative plug of the accumulator.
2. Remove a casing of the air filter (subsection 6.3.1.2 see).
3. Compress fixing clips and disconnect sockets of connection from a potentiometer throttle заслонки, the additional valve of giving of air, the gauge of an air stream and injector wires.
4. Also disconnect a socket of connection of the heating element established between the case throttle заслонки and an inlet collector.
5. Let out pressure from fuel system (subsection 6.3.1.7 see).
6. Then release fixing collars and disconnect a hose of giving of fuel and a hose of the return pipeline from the case throttle заслонки.
7. Disconnect a rope of an accelerator from a cam throttle заслонки on the case throttle заслонки, then turn off a counternut and an adjusting nut and get a braid of a rope from a fixing arm.
8. On models with an automatic transmission also disconnect a rope of fall of transfer.
9. Release fixing collars, then, disconnect hoses of system of cooling behind the case throttle заслонки and stop up apertures of hoses. Make it quickly to minimise loss of a cooling liquid.
10. Remember or mark position of installation of all vacuum and ventilating hoses correctly to connect them at installation of the case throttle заслонки, then, release fixing collars (where are established) and disconnect hoses from the case throttle заслонки.
11. Turn off and remove fixing bolts, крепящие the case throttle заслонки to an inlet collector, and remove the case throttle заслонки from the car.
12. Remove a heating element.
13. Stop up an aperture of an inlet collector with a pure rag that the dirt or extraneous subjects has not got to it.
14. If it is necessary, after removal of the case throttle заслонки turn off fixing screws and divide the top and bottom sections.
15. Remove a lining established between them.

Installation
PERFORMANCE ORDER
1. Installation is spent upside-down removals.
2. At installation it is necessary to pay attention to following moments.
3. If it is necessary, check up, that adjoining surfaces of the top and bottom sections of the case throttle заслонки were pure and dry, then, establish a new lining and collect sections, reliably having tightened fixing screws.
4. Before installation check up, that adjoining surfaces of the case throttle заслонки, an inlet collector and a heating element were pure and equal.
5. Establish the case throttle заслонки and a heating element on an inlet collector.
6. Диагонально tighten all fixing bolts till the demanded moment of an inhaling cтадии 1, then, tighten them till the demanded moment of an inhaling cтадии 2.
7. Check up, that all hoses have been correctly established and if it is necessary, fix them by means of fixing collars.
8. On termination of installation adjust an accelerator rope (the subsection see
6.3.1.3
).
9. On models with an automatic transmission adjust a hill-climbing gear rope (subsection 9.2.4 see).


6.3.1.10. A fuel tank

6.3.1.12. System of injection of fuel / of ignition