Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
6.1. Carburettor engines
6.2. Engines with system of injection of fuel
6.3. System of a food / of release of the fulfilled gases
6.3.1. Models with one-dot electronic injection of fuel
6.3.1.1. Technical characteristics
6.3.1.2. The air filter
6.3.1.3. An accelerator rope
6.3.1.4. An accelerator pedal
6.3.1.5. The gasoline which is not containing тетраэтилсвинца
6.3.1.6. System of injection of fuel
6.3.1.7. Fuel system
6.3.1.8. The fuel pump
6.3.1.9. The gauge of level of fuel
6.3.1.10. A fuel tank
6.3.1.11. The case throttle заслонки
6.3.1.12. System of injection of fuel / of ignition
6.3.1.13. Elements of system of injection of fuel
6.3.1.13.1. A fuel injector
6.3.1.13.2. A regulator of pressure of fuel
6.3.1.13.3. The additional valve of giving of air
6.3.1.13.4. A potentiometer throttle заслонки
6.3.1.13.5. The gauge of a stream of air
6.3.1.13.6. The electromagnetic valve of fast work of the engine
6.3.1.13.7. The temperature valve of the accelerated warming up of the engine
6.3.1.13.8. Демпфер throttle заслонки
6.3.1.13.9. The gauge of an angle of rotation of a cranked shaft
6.3.1.13.10. The capacity transistor
6.3.1.13.11. The gauge of temperature of a cooling liquid
6.3.1.13.12. The gauge of detonation combustion of fuel
6.3.1.13.13. The electronic block of management of the engine
6.3.1.13.14. A heater of a fuel mix
6.3.1.13.15. The switch of neutral transfer
6.3.1.13.16. The switch of blocking of a starter / of lanterns of a backing
6.3.1.13.17. The relay of the electronic block of management of the engine, heating of a fuel mix and the fuel pump
6.3.1.13.18. The switch in system of the hydraulic booster of a steering
6.3.1.13.19. The switch in air central air
6.3.1.14. An inlet collector
6.3.2. Models with multidot electronic injection of fuel
6.4. System of decrease in toxicity of the fulfilled gases
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



6-3-1-13-6-ehlektromagnitnyjj-klapan-bystrojj-raboty-dvigatelya.html

6.3.1.13.6. The electromagnetic valve of fast work of the engine


The electromagnetic valve of fast work of the engine (idling mode) is established on the right party of the case throttle заслонки.

Removal and installation

PERFORMANCE ORDER
1. Before its removal, disconnect a wire of the negative plug of the accumulator.
2. If it is necessary, remove the air filter (subsection 6.3.1.2 see), for access improvement to the valve.
3. Walk along wires of the electromagnetic valve to a socket of connection and disconnect it
4. Unscrew the electromagnetic valve from the case throttle заслонки, remove плунжер, пружинку and a sealing washer.
5. If the electromagnetic valve is replaced, it is necessary to get its wires from a connection socket.
6. If you do not wish to assort a connection socket, the electromagnetic valve can be removed together with a fuel injector and the additional valve of giving of air.
7. Installation is spent upside-down removals.
8. Check up, that плунжер and пружинка have been correctly established.


6.3.1.13.5. The gauge of a stream of air

6.3.1.13.7. The temperature valve of the accelerated warming up of the engine