Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
6.1. Carburettor engines
6.2. Engines with system of injection of fuel
6.3. System of a food / of release of the fulfilled gases
6.3.1. Models with one-dot electronic injection of fuel
6.3.1.1. Technical characteristics
6.3.1.2. The air filter
6.3.1.3. An accelerator rope
6.3.1.4. An accelerator pedal
6.3.1.5. The gasoline which is not containing тетраэтилсвинца
6.3.1.6. System of injection of fuel
6.3.1.7. Fuel system
6.3.1.8. The fuel pump
6.3.1.9. The gauge of level of fuel
6.3.1.10. A fuel tank
6.3.1.11. The case throttle заслонки
6.3.1.12. System of injection of fuel / of ignition
6.3.1.13. Elements of system of injection of fuel
6.3.1.14. An inlet collector
6.3.2. Models with multidot electronic injection of fuel
6.4. System of decrease in toxicity of the fulfilled gases
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



6-3-1-14-vpusknojj-kollektor.html

6.3.1.14. An inlet collector

Removal

PERFORMANCE ORDER
1. Remove the case throttle заслонки, being guided by the instructions resulted in subsection 6.3.1.11.
2. Merge cooling liquid from cooling system, being guided by the instructions resulted in subsection 2.4.5.
3. Remember or mark position of installation of all vacuum hoses and hoses of system of cooling of an inlet collector.
4. Disconnect them from an inlet collector and if it is necessary, from corresponding vacuum valves.
5. Not to mix hoses at installation, mark each of hoses at removal.
6. On models with каталитическим the converter turn off a nut of connection and disconnect a tube рециркуляции the exhaust gases, connecting inlet and final collectors, from the valve on a left-hand side of an inlet collector.
7. Disconnect a socket of connection from the gauge of temperature of a cooling liquid on the right party of a collector.
8. If it is necessary, turn off fixing bolts and disconnect a wire (weights (from an inlet collector.
9. Turn off fixing bolts and remove a fixing arm behind an inlet collector.
10. Check up, that all vacuum / ventilating hoses have been disconnected from an inlet collector.
11. Upside-down turn off and remove fixing nuts and bolts.
12. Remove an inlet collector from a head of the block of cylinders and get it from an impellent compartment, then remove a lining of an inlet collector and will throw out it.

Installation

PERFORMANCE ORDER
1. Installation is spent upside-down removals.
2. At installation pay attention to following moments.
3. Check up, that adjoining surfaces of an inlet collector and a head of the block of cylinders were pure and dry, and establish a new lining on bolts of a head of the block of cylinders.
4. Establish an inlet collector and tighten fixing nuts and bolts till the demanded moment of an inhaling in that order.
5. Check up, that all corresponding hoses have been connected correctly and reliably fastened (where it is necessary) by means of fixing collars.
6. Establish the case throttle заслонки, being guided by the instructions resulted in subsection 6.3.1.11.
7. On termination of installation fill in cooling liquid in cooling system.


6.3.1.13.19. The switch in air central air

6.3.2. Models with multidot electronic injection of fuel