Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
6.1. Carburettor engines
6.2. Engines with system of injection of fuel
6.3. System of a food / of release of the fulfilled gases
6.3.1. Models with one-dot electronic injection of fuel
6.3.2. Models with multidot electronic injection of fuel
6.3.2.1. Technical characteristics
6.3.2.2. The air filter
6.3.2.3. An accelerator rope
6.3.2.4. An accelerator pedal
6.3.2.5. System of injection of fuel
6.3.2.6. Fuel system
6.3.2.7. The fuel pump
6.3.2.8. The gauge of level of fuel
6.3.2.9. A fuel tank
6.3.2.10. The case throttle заслонки
6.3.2.11. Elements of system of injection of fuel (engines in volume 1,6)
6.3.2.12. Elements of system of injection of fuel (engines in volume 2,0)
6.3.2.13. An inlet collector
6.4. System of decrease in toxicity of the fulfilled gases
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



6-3-2-10-korpus-drosselnojj-zaslonki.html

6.3.2.10. The case throttle заслонки


Fixing bolts of the case throttle заслонки have dressed of 1,6 l with the engine in volume

Fixing bolts – are specified by arrows

Removal

PERFORMANCE ORDER
Models with the engine in volume of 1,6 litres
1. Disconnect a wire of the negative plug of the accumulator.
2. Remove a casing of the air filter, being guided by the instructions resulted in subsection 6.3.2.2.
3. Compress fixing clips and disconnect sockets of connection from a potentiometer throttle заслонки, the additional valve of giving of air, the gauge of an air stream and the electromagnetic valve of increase in speed of work of the engine in an idling mode.
4. Disconnect a rope of an accelerator from a cam throttle заслонки. Turn off a counternut and an adjusting nut, and get a braid of a rope from a fixing arm.
5. Remember or mark position of installation of all vacuum and ventilating hoses correctly to connect them at installation of the case throttle заслонки, then, release fixing collars (where are established) and disconnect hoses from the case throttle заслонки.
6. Release fixing collars, then, disconnect hoses of system of cooling from both parties of the case throttle заслонки and stop up apertures of hoses. Make it quickly to minimise loss of a cooling liquid.
7. Turn off and remove fixing bolts, крепящие the case throttle заслонки to an inlet collector, and remove the case throttle заслонки from the car. Remove a lining and will throw out it; at installation use the new. Stop up an aperture of an inlet collector with a pure rag that the dirt or extraneous subjects has not got to it.
Models with the engine in volume of 2,0 litres
8. Release a fixing collar and disconnect an inlet air pipe from the case throttle заслонки.
9. Disconnect a socket of connection from a potentiometer throttle заслонки.
10. On models "Phase I" accurately disconnect a rod of the connecting mechanism of an accelerator from the spherical hinge on the case throttle заслонки.
11. On models "Phase II" disconnect a rope of an accelerator from a cam throttle заслонки. On models with an automatic transmission, also, disconnect a rope of fall of transfer.
12. On all models release fixing collars, disconnect hoses of system of cooling from the case throttle заслонки and stop up apertures of hoses. Make it quickly to minimise loss of a cooling liquid.
13. On all models, remember or mark position of installation of all vacuum and ventilating hoses correctly to connect them at installation of the case throttle заслонки, then, release fixing collars (where are established) and disconnect hoses from the case throttle заслонки.
14. If it is necessary, remove a fixing arm of an inlet collector for access reception to bolts of fastening of the case throttle заслонки.

15. Turn off and remove fixing bolts, крепящие the case throttle заслонки to an inlet collector, and remove the case throttle заслонки from the car. Remove a lining and will throw out it; at installation use the new. Stop up an aperture of an inlet collector with a pure rag that the dirt or extraneous subjects has not got to it.


Installation

PERFORMANCE ORDER
1. Installation is spent upside-down removals. Before installation check up, that adjoining surfaces of the case throttle заслонки and an inlet collector were pure and equal.
2. Establish a new lining on an inlet collector. Establish the case throttle заслонки on an inlet collector, then, диагонально tighten all fixing bolts till the demanded moment of an inhaling of a stage 1, then, tighten them till the demanded moment of an inhaling of a stage 2 (subsection 6.3.2.1 see).
3. Check up, that all hoses have been correctly established and if it is necessary, fix them by means of fixing collars;
4. On termination of installation adjust an accelerator rope, being guided by the instructions resulted in subsection 6.3.2.3.
5. On models with an automatic transmission adjust a rope of fall of transfer, being guided by the instructions resulted in subsection 9.2.4.


6.3.2.9. A fuel tank

6.3.2.11. Elements of system of injection of fuel (engines in volume 1,6)