Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
6.1. Carburettor engines
6.2. Engines with system of injection of fuel
6.3. System of a food / of release of the fulfilled gases
6.3.1. Models with one-dot electronic injection of fuel
6.3.2. Models with multidot electronic injection of fuel
6.3.2.1. Technical characteristics
6.3.2.2. The air filter
6.3.2.3. An accelerator rope
6.3.2.4. An accelerator pedal
6.3.2.5. System of injection of fuel
6.3.2.6. Fuel system
6.3.2.7. The fuel pump
6.3.2.8. The gauge of level of fuel
6.3.2.9. A fuel tank
6.3.2.10. The case throttle заслонки
6.3.2.11. Elements of system of injection of fuel (engines in volume 1,6)
6.3.2.11.1. A fuel collector and fuel injectors
6.3.2.11.2. A regulator of pressure of fuel
6.3.2.11.3. A potentiometer throttle заслонки
6.3.2.11.4. The additional valve of giving of air
6.3.2.11.5. The gauge of a stream of air
6.3.2.11.6. The electromagnetic valve of fast work of the engine
6.3.2.11.7. The temperature valve of the accelerated warming up of the engine
6.3.2.11.8. The gauge of an angle of rotation of a cranked shaft and the capacity transistor
6.3.2.11.9. The gauge of temperature of a cooling liquid
6.3.2.11.10. The electronic block of management of the engine
6.3.2.11.11. The switch of neutral transfer
6.3.2.11.12. The switch of blocking of a starter / of lanterns of a backing
6.3.2.11.13. The relay of the electronic block of management of the engine and the fuel pump
6.3.2.11.14. The switch in system of strengthening of a steering
6.3.2.11.15. The switch in air central air
6.3.2.11.16. The gauge of speed of movement of the car
6.3.2.12. Elements of system of injection of fuel (engines in volume 2,0)
6.3.2.13. An inlet collector
6.4. System of decrease in toxicity of the fulfilled gases
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



6-3-2-11-6-ehlektromagnitnyjj-klapan-bystrojj-raboty-dvigatelya.html

6.3.2.11.6. The electromagnetic valve of fast work of the engine

The electromagnetic valve of increase in speed of work of the engine in an idling mode
The electromagnetic valve – is specified by an arrow.

The electromagnetic valve of fast work of the engine in an idling mode is established on the forward party of the case throttle заслонки.

Before its removal, disconnect a wire of the negative plug of the accumulator.

If it is necessary, remove the air filter, being guided by the instructions resulted in subsection 6.3.2.2, for access improvement to the valve.

Removal and installation

PERFORMANCE ORDER
1. Disconnect a socket of connection from the electromagnetic valve.
2. Unscrew the electromagnetic valve from the case throttle заслонки, remove плунжер, пружинку and a sealing washer.
3. Installation is spent upside-down removals. At installation use a new sealing washer. Check up, that плунжер and пружинка have been correctly established.



6.3.2.11.5. The gauge of a stream of air

6.3.2.11.7. The temperature valve of the accelerated warming up of the engine