Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
6.1. Carburettor engines
6.2. Engines with system of injection of fuel
6.3. System of a food / of release of the fulfilled gases
6.3.1. Models with one-dot electronic injection of fuel
6.3.2. Models with multidot electronic injection of fuel
6.3.2.1. Technical characteristics
6.3.2.2. The air filter
6.3.2.3. An accelerator rope
6.3.2.4. An accelerator pedal
6.3.2.5. System of injection of fuel
6.3.2.6. Fuel system
6.3.2.7. The fuel pump
6.3.2.8. The gauge of level of fuel
6.3.2.9. A fuel tank
6.3.2.10. The case throttle заслонки
6.3.2.11. Elements of system of injection of fuel (engines in volume 1,6)
6.3.2.12. Elements of system of injection of fuel (engines in volume 2,0)
6.3.2.12.1. A fuel collector and fuel injectors
6.3.2.12.2. A regulator of pressure of fuel
6.3.2.12.3. A potentiometer throttle заслонки
6.3.2.12.4. The gauge of a stream of air
6.3.2.12.5. The additional valve of giving of air
6.3.2.12.6. The electromagnetic valve of fast work of the engine
6.3.2.12.7. The block of adjustment of giving of air (an idling mode)
6.3.2.12.8. The valve of adjustment of receipt of air
6.3.2.12.9. The gauge of an angle of rotation of a cranked shaft
6.3.2.12.10. The capacity transistor
6.3.2.12.11. The gauge of detonation combustion of fuel
6.3.2.12.12. The electronic block of management of engine work
6.3.2.12.13. The switch of neutral transfer
6.3.2.12.14. The switch of blocking of a starter / of lanterns of a backing
6.3.2.12.15. The relay of the electronic block of management engines and the fuel pump
6.3.2.12.16. The switch in system of strengthening of a steering
6.3.2.12.17. The switch in air central air
6.3.2.12.18. The gauge of speed of movement of the car
6.3.2.13. An inlet collector
6.4. System of decrease in toxicity of the fulfilled gases
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



6-3-2-12-3-potenciometr-drosselnojj-zaslonki.html

6.3.2.12.3. A potentiometer throttle заслонки


Arrangement of a potentiometer throttle заслонки models "Phase II"

The arrangement of a potentiometer throttle заслонки is specified by an arrow.

The potentiometer throttle заслонки is established on the back party of the case throttle заслонки.

Before its removal, disconnect a wire of the negative plug of the accumulator.

Removal and installation

PERFORMANCE ORDER
1. Disconnect a socket of connection of a potentiometer throttle заслонки.
2. By means of a white paint or a marker make marks in the case throttle заслонки and a potentiometer.
3. Turn off two fixing screws and remove a potentiometer.
4. At installation, establish a potentiometer on the case throttle заслонки so that its lever has been correctly established on the lever of an axis throttle заслонки.
5. Combine the marks made before removal, and twirl fixing screws a little. Adjust a potentiometer as follows.
6. By means of a tester established on measurement of resistance, check up, that resistance of a potentiometer was such as it is specified in section of technical characteristics (see subsection 6.3.2.1). If it is necessary, turn off fixing screws and turn a potentiometer that its resistance was such as it is specified in section of technical characteristics.
7. When the potentiometer will be correctly established, reliably tighten fixing screws, and connect a connection socket.
8. Connect a wire of the negative plug of the accumulator.


6.3.2.12.2. A regulator of pressure of fuel

6.3.2.12.4. The gauge of a stream of air