Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
6.1. Carburettor engines
6.2. Engines with system of injection of fuel
6.3. System of a food / of release of the fulfilled gases
6.3.1. Models with one-dot electronic injection of fuel
6.3.2. Models with multidot electronic injection of fuel
6.3.2.1. Technical characteristics
6.3.2.2. The air filter
6.3.2.3. An accelerator rope
6.3.2.4. An accelerator pedal
6.3.2.5. System of injection of fuel
6.3.2.6. Fuel system
6.3.2.7. The fuel pump
6.3.2.8. The gauge of level of fuel
6.3.2.9. A fuel tank
6.3.2.10. The case throttle заслонки
6.3.2.11. Elements of system of injection of fuel (engines in volume 1,6)
6.3.2.12. Elements of system of injection of fuel (engines in volume 2,0)
6.3.2.12.1. A fuel collector and fuel injectors
6.3.2.12.2. A regulator of pressure of fuel
6.3.2.12.3. A potentiometer throttle заслонки
6.3.2.12.4. The gauge of a stream of air
6.3.2.12.5. The additional valve of giving of air
6.3.2.12.6. The electromagnetic valve of fast work of the engine
6.3.2.12.7. The block of adjustment of giving of air (an idling mode)
6.3.2.12.8. The valve of adjustment of receipt of air
6.3.2.12.9. The gauge of an angle of rotation of a cranked shaft
6.3.2.12.10. The capacity transistor
6.3.2.12.11. The gauge of detonation combustion of fuel
6.3.2.12.12. The electronic block of management of engine work
6.3.2.12.13. The switch of neutral transfer
6.3.2.12.14. The switch of blocking of a starter / of lanterns of a backing
6.3.2.12.15. The relay of the electronic block of management engines and the fuel pump
6.3.2.12.16. The switch in system of strengthening of a steering
6.3.2.12.17. The switch in air central air
6.3.2.12.18. The gauge of speed of movement of the car
6.3.2.13. An inlet collector
6.4. System of decrease in toxicity of the fulfilled gases
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956



6-3-2-12-7-blok-regulirovki-podachi-vozdukha-rezhim-kholostogo-khoda.html

6.3.2.12.7. The block of adjustment of giving of air (an idling mode)


The block of adjustment of giving of air at engine work in an idling mode is established on the right party of an inlet collector.

Before its removal, disconnect a wire of the negative plug of the accumulator.

Removal and installation

PERFORMANCE ORDER
1. Disconnect sockets of connection from the additional valve of adjustment of giving of air and the electromagnetic valve of fast work of the engine in an idling mode, and get wires from fixing clips.
2. Turn off fixing bolts and remove the block from an inlet collector. Remove a lining and will throw out it; at installation it is necessary to use the new.
3. At installation check up, that adjoining surfaces of the block and an inlet collector were pure and dry, then, establish a new lining. Establish a nut of adjustment of giving of air, and reliably tighten fixing bolts. Connect sockets of connection and a wire of the negative plug of the accumulator.


6.3.2.12.6. The electromagnetic valve of fast work of the engine

6.3.2.12.8. The valve of adjustment of receipt of air