Service Nissan Sunny with 1991 on 1997 of release in a body n-14.
1. The maintenance instruction
2. Maintenance service
3. Engines
4. Cooling system
5. Heating and ventilation system
6. Fuel and an exhaust system
6.1. Carburettor engines
6.2. Engines with system of injection of fuel
6.3. System of a food / of release of the fulfilled gases
6.3.1. Models with one-dot electronic injection of fuel
6.3.2. Models with multidot electronic injection of fuel
6.3.2.1. Technical characteristics
6.3.2.2. The air filter
6.3.2.3. An accelerator rope
6.3.2.4. An accelerator pedal
6.3.2.5. System of injection of fuel
6.3.2.6. Fuel system
6.3.2.7. The fuel pump
6.3.2.8. The gauge of level of fuel
6.3.2.9. A fuel tank
6.3.2.10. The case throttle заслонки
6.3.2.11. Elements of system of injection of fuel (engines in volume 1,6)
6.3.2.12. Elements of system of injection of fuel (engines in volume 2,0)
6.3.2.12.1. A fuel collector and fuel injectors
6.3.2.12.2. A regulator of pressure of fuel
6.3.2.12.3. A potentiometer throttle заслонки
6.3.2.12.4. The gauge of a stream of air
6.3.2.12.5. The additional valve of giving of air
6.3.2.12.6. The electromagnetic valve of fast work of the engine
6.3.2.12.7. The block of adjustment of giving of air (an idling mode)
6.3.2.12.8. The valve of adjustment of receipt of air
6.3.2.12.9. The gauge of an angle of rotation of a cranked shaft
6.3.2.12.10. The capacity transistor
6.3.2.12.11. The gauge of detonation combustion of fuel
6.3.2.12.12. The electronic block of management of engine work
6.3.2.12.13. The switch of neutral transfer
6.3.2.12.14. The switch of blocking of a starter / of lanterns of a backing
6.3.2.12.15. The relay of the electronic block of management engines and the fuel pump
6.3.2.12.16. The switch in system of strengthening of a steering
6.3.2.12.17. The switch in air central air
6.3.2.12.18. The gauge of speed of movement of the car
6.3.2.13. An inlet collector
6.4. System of decrease in toxicity of the fulfilled gases
7. System of start-up of the engine
8. Coupling
9. Transmissions
10. Semiaxes
11. Brakes
12. Suspension brackets and a steering
13. A body
14. An electric equipment
 




6ac69956 Мультимарочный сканер по материалам obd-2.ru.
расчет калорий для похудения
Лучшая gsm сигнализация для дома смотрите на http://www.napulte.ru.
мрт пояснично-крестцового отдела позвоночника: сделать по.


6-3-2-12-8-klapan-regulirovki-postupleniya-vozdukha.html

6.3.2.12.8. The valve of adjustment of receipt of air


MODELS "PHASE I"

The valve of adjustment of receipt of air is established under an inlet collector.

Before its removal, disconnect a wire of the negative plug of the accumulator.

Removal and installation
PERFORMANCE ORDER
1. For access improvement put the car on a manual brake, then, lift a forward part of the car and establish it on support. Then, access to the valve can be received from above and from below.
2. Disconnect a socket of connection of the valve, then, release fixing collars and disconnect vacuum hoses and hoses of system of cooling. Quickly stop up apertures of hoses of system of cooling to prevent fuel leak.
3. Turn off and remove fixing bolts, then, remove the valve from an inlet collector.
4. Installation is spent upside-down removals.

MODELS "PHASE II"

The valve of adjustment of receipt of air is established on a left-hand side of an inlet collector, hardly below the block of adjustment of giving of air at engine work in an idling mode.

Before its removal, disconnect a wire of the negative plug of the accumulator.

The valve of adjustment of receipt of air – models "Phase II"

1. Vacuum hoses

2. Fixing bolts

Removal and installation
PERFORMANCE ORDER
1. Remove the top section of an inlet collector, being guided by the instructions resulted in subitem 20-25 of subsection 6.3.2.13.
2. Release fixing collars and disconnect both vacuum hoses from the valve.
3. Turn off and remove fixing bolts, then, remove the valve from an inlet collector.
4. Installation is spent upside-down removals.

6.3.2.12.7. The block of adjustment of giving of air (an idling mode)
6.3.2.12.9. The gauge of an angle of rotation of a cranked shaft